Bobrick B740-115V Surface-Mounted Eclipse Automatic Hand Dryer

SKU: B740-115V
$418.97
Weight: 13.54 LBS
Bobrick

Call us: 1-800-992-3667

FACTORY LEAD TIMES
MAY VARY

Actual products may differ
slightly in appearance
to images shown.

Details

Details

White surface-mounted Eclipse® automatic hand dryer


Features

  • Vitreous enamel, drawn-steel cover, white only
  • 115V AC, 20 Amp, 2400 Watts, 50/60 Hz, cULus Listed
  • Limited warranty: motor brushes for 3 years; all other parts for 10 years
  • Automatic hand dryers should be installed 15" (380mm) above any projection or horizontal surface which may interfere with the operation of the automatic sensor

Specifications

Materials: Cover - One-piece, deep-drawn, 16-gauge (1.6mm) thick steel finished in high-gloss, acid-resistant vitreous enamel or bright polished chrome-plated finish. Cover is secured to mounting base by a retaining bracket and to the air inlet/outlet grille by a single concealed locking screw
Air Inlet/Outlet Grille - Vandal-resistant, pressure die-cast aluminium. Includes infrared sensor and operational graphics. Fixed to the mounting base by two screws and to the cover by one screw
Mounting Base - 16-gauge (1.6mm) thick plated-steel with three 1/4" (6mm) diameter mounting holes and one 7/8" (22mm) diameter hole for electrical supply wiring
Fan - Dynamically balanced, single inlet, directs air flow in a wide band through heating element at 105 cfm
Motor - Universal, 1/10 hp, 6200 rpm with sealed ball bearing at drive shaft end and self-lubricating sleeve bearing at nondrive end. Equipped with automatic thermal-overload switch
Heating Element - Coiled nickel-chrome wire is mounted on mica formers and equipped with automatic thermal-overload switch. Black, injection molded element housing is mounted on the fan inlet, heats air without hot spots - inaccessible to vandals
Electronic Control - Infrared automatic sensor automatically turns dryer on when hands are held under air-outlet opening and across path of sensor. Remove hands from path of sensor and dryer stops. Electronic sensor has automatic shutoff approximately 1-1/2 minutes after dryer turns on if an inanimate object, such as tape or chewing gum, is placed across sensor lens. After inanimate object is removed, electronic sensor automatically resets itself and dryer operates normally
Size: 15-7/16" (390mm) w x 8-7/8" (225mm) h x 7-9/16" (190mm) d
Warranty 10-year Limited Warranty
Operation: No-touch operation: electronic sensor automatically turns dryer on when hands are held under air-outlet opening and across path of sensor. Remove hands and dryer stops. Dryer will not stop by itself before user is satisfied hands are dry. Dryer operates only when actually drying hands which saves energy and operating costs. Electronic sensor will automatically shut dryer off 1-1/2 minutes after dryer turns on if an inanimate object, such as tape or chewing gum, is placed across air-outlet opening. After inanimate object is removed, electronic sensor automatically resets itself and dryer operates normally
Installation: Wall Preparation:
Secure mounting base on wall using template provided. For masonry walls, provide three #10 expansion shields or anchors and secure with four #10 (M4.8) sheet-metal screws (not furnished). For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with three #10 (M4.8) round-head sheet-metal screws or 3/16" (5mm) toggle bolts (not furnished). Provide electrical service from nearest distribution panel to dryer mounting base in compliance with local electrical codes
Wiring Instructions:
Connect ground wire to ground terminal marked, the black or hot wire to terminal marked L1, and neutral or white wire to terminal marked N. A DEDICATED LINE IS REQUIRED FOR EACH 115-VOLT INSTALLATION
Notes: Electronic sensor in the Eclipse dryer will pick up movement within 6" (150mm) of the air-outlet opening. Use caution when choosing location for Eclipse dryers in confined areas. Consider proximity to doorways and other traffic areas
Bobrick automatic hand dryers should be installed 15" (380mm) above any projection or horizontal surface which may interfere with the operation of the automatic sensor

Certifications

UL: cULs Listed
VDE: VDE Approved
EU Directives: Complies with ROHS and CE Marked