Bobrick B750-115V Recessed Aircraft Automatic Hand Dryer

SKU: B750-115V
$808.67
Weight: 43.23 LBS
Bobrick

Call us: 1-800-992-3667

FACTORY LEAD TIMES
MAY VARY

Actual products may differ
slightly in appearance
to images shown.

Details

Details

Recessed automatic hand dryer


Features

  • Meets ADA Accessibility Guidelines for barrier-free installation
  • Vitreous enamel, drawn-steel cover, white only
  • 115V AC, 20 Amp, 2300 Watts, 50/60 Hz, cULus Listed
  • Limited warranty: motor brushes for 3 years; all other parts for 10 years
  • Automatic hand dryers should be installed 15" (380mm) above any projection or horizontal surface which may interfere with the operation of the automatic sensor

Specifications

Materials: Cover - One-piece, minimum 1/8'' (3mm) thick, grey iron-casting is finished in high-gloss, acid-resistant, multicoat vitreous enamel. Equipped with a two-position, self-returning, chrome-plated air-outlet nozzle. Air-outlet opening is equipped with vandal resistant grille. Cover is secured to base unit with two concealed, vandal-resistant, recessed hex-screws
Recessed Mounting Box - 16-gauge (1.5mm) steel with baked enamel finish. Rust-resistant
Base Unit - One-piece aluminum casting. Incorporates concealed, vandal-resistant air-inlet vanes on both sides and bottom
Motor - Universal, 1/10 hp, 6200 rpm, on resilient mounting. Sealed ball bearing at drive-shaft end and self-lubricating sleeve bearing at nondrive end. Equipped with automatic thermal-overload switch
Fan - Dynamically balanced, single-inlet centrifugal fan is mounted on motor shaft; directs airflow through heating element at 150 cfm
Heating Element - Coiled nickel-chrome heating element is mounted in mica frame and protected by an automatic thermal overload switch. Heating element, which is located on inlet side of fan, heats air without hot spots — inaccessible to vandals
Electronic Control - Infrared sensor automatically turns dryer on when hands or self-returning nozzle are held under ai routlet opening and across path of sensor. Remove hands or release self-returning nozzle from path of sensor and dryer stops. Electronic sensor has automatic shutoff approximately 1-1/2 minutes after dryer turns on if an inanimate object is placed across air-outlet opening. After inanimate object is removed, electronic sensor automatically resets itself and dryer operates normally
Size: 15-1/4" (385mm) w x 11-7/8" (300mm) h x 4" (100mm) d
Warranty: 10-Year Limited Warranty
Operation: Cover projects no more then 4" (100mm) from wall, to comply with barrier-free accessibility guidelines (including ADAAG in the U.S.A.). No-touch operation: electronic sensor automatically turns dryer on when hands or self-returning nozzle are held under air-outlet opening and across path of sensor. Two-position nozzle is adjustable to direct airflow: up position directs airflow down for hand drying and down position directs airflow up for face drying. After drying face, release nozzle and it automatically returns to up position. Remove hands or release self-returning nozzle from path of sensor and dryer stops. Dryer will not stop by itself before user is satisfied hands or face are dry. Dryer operates only when actually drying hands or face, which saves energy and operating costs. Electronic sensor will automatically shut dryer off 1-1/2 minutes after dryer turns on if inanimate object, such as tape or chewing gum, is placed across air-outlet opening. After inanimate object is removed, electronic sensor automatically resets itself and dryer operates normally
Installation: Provide framed rough wall opening 13-3/4" wide x 9-1/2" high (350 x 240mm). Minimum recessed depth required to finish face of wall is 3-3/4" (95mm). Allow clearance for construction features that may protrude into rough wall opening from opposite wall. Coordinate with mechanical engineer to avoid pipes, vents, and conduits. If installed in plaster wall, it is recommended that opening be grounded on all four sides with metal plaster trim. If unit projects above top of wainscot, provide aluminum channel or other filler to eliminate gap between flange of mounting box and finish face of wall. If two units are installed back-to-back, a sound-barrier is recommended between units. Provide shims between framing and mounting box at all points indicated by an S, then secure with four #10 (M4.8) screws (not furnished). Provide electrical service from nearest distribution panel to recessed mounting box in conformance with local electrical codes
Wiring Instructions:
Connect ground wire to ground terminal marked, the black or hot wire to terminal marked L1, and neutral or white wire to terminal marked N. A DEDICATED LINE IS REQUIRED FOR EACH 115-VOLT INSTALLATION
Notes: Electronic sensor in AirCraft dryers will pick up movement within 7-1/2" (190mm) of air-outlet nozzle. Use caution when choosing location for AirCraft dryers in confined areas. Consider proximity to doorways and other traffic areas
Bobrick automatic hand dryers should be installed 15" (380mm) above any projection or horizontal surface which may interfere with the operation of the automatic sensor

Certifications

Barrier-Free Code Compliance: Comply with barrier-free accessibility guidelines (including ADAAG in the U.S.A.)
UL: cULs Listed
VDE: VDE Approved
China Compulsory Certificate: CCC Approved
EU Directives: Complies with ROHS and is CE Marked